PVC Insulated Cable
1) Used in permanent power equipment and lighting installations. 2) AC circuit. 3) Rate voltage up to 450/750V. 4) Highest conductor temperature: 90^oC. 5) Cable installation temperature: not lower than 0^oC. 6) Permissible curved radius (cable outer diameter): smaller than 25mm, not less than 4D cables with outer diameter of 25mm or above (not less than 6D). 7) Models: a) 227IEC01 (BV): general single-core copper conductor PVC insulation rigid cable ; b) 227IEC02 (RV): general single-core copper conductor PVC insulation flexible cable ; c) 227IEC05 (BV): solid copper conductor single-core PVC insulation cable for inner wiring ; d) 7IEC06 (RV): copper conductor single-core PVC insulation flexible cable for inner wiring. 8) Wiring: a) 227IEC10 (BVV): light PVC sheathed cable ; b) 7IEC52 (RVV) ; c) 227IEC53 (RVV)..

Flame Resistance Mica Cable Tape
Mica tape consists of the heat resistant phlogopite mica paper or synthetic mica paper bonded to an electrical grade glass cloth as the supporting fabric, impregnated with a specially selected high temperature resistant silicon resin. For excellent flame resisting characteristics, it has been widely used for power and control cables and instrumentation and signaling cables. Due to the very high flexibility and high tensile strength, this tape can be easily applied with high speed standard taping equipment. Specifications: 1) Width: 6 - 1000mm ; 2) Length: 300m,500m,1000m ; 3) Standard cores: 52mm,54mm,76mm

Bolt-connected Fuses - RT12
Used in a power distribution installation with rated voltage of AC 380V, rated current up to 100A for overload and short-circuit protection. When combined with a fuse type isolator, the fuse with an electric impinger can be used for phase-lack protection

Porcelain Insulators
1) Line type porcelain insulator ; 2) Distribution type bushing ; 3) High voltage insulator

Insulator and Fittings
We can supply the following products for you as per IEC, ANSI, BS, AS, DIN, CAN: 1. Porcelain Insulator: 1.1 45KN-530KN (D.C.) Normal type and Anti-pollution type suspension porcelain insulator ; 1.2 6KV-36KV pin type porcelain insulator ; 1.3 Line& pin post porcelain insulator ; 1.4 Long-rod suspension porcelain insulator ; 1.5 Cross-arm insulator ; 1.6 Stay insulator
1.7 Shackle insulator ; 1.8 Spool insulator. 2. Glass Insulator: 70KN-300KN (D.C) Normal type & anti-pollution toughened glass insulator. 3. Silicone Rubber Composite Insulator: 3.1 70KN-300KN suspension silicone rubber insulator ; 3.2 (Line) Post composite insulator ; 3.3 Composite crossing arm insulator; 3.4 Pin type composite insulator ; 3.5 Composite insulator for locomotive electrified railway ; 3.6 10/35 A.C. outdoor high-voltage composite drop-out fuse ; 3.7 Outdoor high-voltage composite disconnecting switch ; 3.8 Composite suspension insulator for earth line.

Bus Bar Insulators
1) Mainly made of bulk molding compound, unsaturated polymer with fiber glass ; 2) Good electrical resistance, heat resistance, fire resistance, low shrinkage and water resistance properties

Copper Clad Laminates
We supply all types of copper/AL clad laminates such as; xpc, fr-1, fr-2, fr-4, cem-1, cem-3, flexibles and insulating materials, from high quality Chinese manufacturers, with quite competitive prices.

PU Tubing
1) Overpressure resistant property: 16kg/cm² ; 2) Max. working pressure: 24kg/cm² ; 3) Stretch resistance: 400kg/cm² ; 4) Tearing strength: 110kg/cm² ; 5) Anti-abrasion: 35mg

PVC Insulation Tapes
1) Made from polyvinyl choride (PVC) as backing material ; 2) Coated with rubber pressure-sensitive adhesive ; 3) Resistant to high voltage, fire and weather ; 4) Designed for connecting separated electrical wires for electrical insulating and protection purposes ; 5) Backing: PVC film ; 6) Thickness: 0.12 - 0.20mm ; 7) Tensile strength: >15N/cm ; 8) Extension rate at break: >200% ; 9) 180 peeling strength: <1.5 ; 10) Withstand voltage (5kV x 1min): now-breakdown ; 11) Persistent adhesion (min): 10.

MTriple Insulated Wire
1) Applications: CB-TIW Triple Insulated Wire is used in the winding of micro-transformers built into personal computers, cell phones, inverters, IT equipment and other similar devices. 2) Conductor: metal wire, tin plated metal wire, enameled metal wire. 3) Insulation layers: a) 2 layers of thermoplastic polyester elastomer ; b) Polyamide. 4) Rated Voltage: 1.41kV. 5) Rated Temperature: 130oC. 6) Benefits: a) Winding is made easy ; b) Save insulation tapes and barriers because of its high breakdown voltage ; c) High speed automatic winding because of its high resistance to abrasion

Compound Insulators
1) Compound insulators have high electrical performance, and silicon rubber sleeves are the good hydrophone and have water floating capacity, heavy pollution resistance, can prevent flashover due pollution. It can work on the severely polluted sites without special clearing ; 2) High mechanical strength, the anti-bent and anti-pull capacity of the glass fiber rod is several or even ten times of the porcelain type. Also, the anti-impact and anti- shaking capacity is excellent. Compound-rod, cross-arm will never occur the cracks which do to porcelain insulators. 3) Compound insulators are generally small, and light (about 1/5 and 1/10 respectively), easy to carry and install

Enamel Insulation
Thin insulation in the form of enamel makes the electronic transformation possible with great efficiency through Copper & Aluminium conductors. We can offer Wire Enamels based on Modified Polyester, Polyurethane & Polyesterimide and i.e. from class B (130 degree) to class H (180 degree) and Polyamide imide ( Top Coat ) suitable for fine & thick wires, including strips.

Battery Insulation Sheet
1) Material: Toray, Dupont, ITWFormex, GE, NOMEX, Bergquist, etc. ; 2) Good insulation and flaming characteristics with SGS and UL inspection report ; 3) Can be used in batteries, power and all kinds of electron products

Electric Insulation Products
Electric insulation products: fiberglass sleeving, mica sheet and tape, insulation paper and board, phenolic cotton rod and laminate, PVC self-adhesive insulation tape, non-alkali fiberglass tape, non-alkali fiberglass cloth, polyester film and etc.

Heat-Shrinkable Tubes
Features of  good insulation, flame-resistance and shock aging,  the products are wide applied in the communication, electron, aviation, and war industry field.

Mica Abnormal Parts
Mica abnormal parts made of mica, through roll up, rushing, lathing, drilling, grinding, milling etc, and form up to angle shaped, "I"-shaped, and through shaped parts.

Anti-Track Tubing
Excellent performance of flame retardant, insulation, flexibility and low shrinkable temperature. Widely used in wire terminals insulation, bond of wire harness, mechanical protection, resistance and capacitor protection.

Probe
Place of Origin: China. These series products for pre-mix gas burners have been used extensively in hot water boilers, ovens, condensing boilers, air heaters, drying machines, spray booths, process heaters, range cookers and steam boilers.

3 1/2 Digital Insulation Test Meter
1) Function: insulation test ; 2) Display: 3 1/2 digit LCD with a max. reading of 1999 ; 3) Test voltage 250V/500V/1000V ; 4) Back light ; 5) LED high voltage indication ; 6) Safety: according to EN61010-1 protection class II over voltage category (CAT III 600V) pollution degree 2 ; 7) Power supply: 9V zinc-carbon battery. ; 8) Size: 155(H) x 97(W) x 50(D)mm ; 9) Weight: approx. 320g (including battery)

Pole Type Insulator
Applying for insulating for high-voltage transmit electricity aerial cable and fixing up lead, string lines for different grades of voltage. We're a manufacturer and exporter in various kinds of insulators in china.

1kV Inter-Connection Covers, Heat Shrink Cable
These covers are divided into 2-core, 3-core, 4-core and 5-core cross-sections to hold cable: 10 - 400mm2.

Magnesium Oxide, electrical grade
Destination: Tubular heating elements. Properties:Excellent electric insulation and heat transfer in working temperature. Work temperature: <= 1000 C? ; Apertures: 50 - 325( According to American Standard ASTM.) ; Flow speed(F.T)(s/100g): 36+/- 2  (Taking 4# fort cup as standard.S/100g) ; Density(TD)(g/cm3): 2.30+/- 0.03 ; Ordinary state:Insulation resistance(MΩ): > 1000 ; Ordinary state: Voltage resistance (V): > 2000 ; Thermal state: Surface load (w/cm?: 10 ; Thermal state: Insulation resistance (MΩ):>10 ; Thermal state: Voltage resistance (V): > 1500 ; Thermal state: Leak current (MA): > 0.3 ; Chemical composition: MgO: 96.5%min. ; SiO2:1.5%max.  CaO:1.5%max.  Al2O3:0.15%max. ; Fe2O3:0.3%max.  (BD): 3.45% max.   Loss: 0.35% max.

25k Composite Tension / Suspension Insulator
Features: 1) Manufactured by means of injection whole-molding technology
2) The juncture between end fitting and core is totally embedded in HTV silicone rubber, eliminating conventional and traditional seal defects. Materials: 1) Silicon Rubber for sheds/ housing ; 2) Glass-fiber reinforced epoxy resin rod (ECR type) for core ; 3) Hop dip galvanized cast steel for metal fittings. Electromechanical specifications: 1) Rated voltage: 25kV ; 2) Specified mechanical load (tensile): 100kN ; 3) Arcing distance: 516mm ; 4) Creepage distance: 1600 mm ; 5) Section length: 840mm ; 6) Lightning impulse withstand voltage (Peak value): 310kV ; 7) Wet 1 min power-frequency withstand voltage (Effective value): 150kV ; 8) Pollution withstand voltage(Under saline density 0.35mg/cm2): 32